Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wellborn Roofing: The Fort Lauderdale Owner’s Guide
Wellborn roofing parts and materials in Fort Lauderdale typically run $400 to $1,800 for repairs and $8,000 to $20,000 for a full replacement, installed, depending on what failed and how much of the roof is involved. We stock common Wellborn-compatible flashing, underlayment, fasteners, and trim profiles on our trucks so a single service call usually gets you diagnosed and fixed in one visit. Most Fort Lauderdale homeowners discover a Wellborn roofing problem one of two ways: a water stain spreading across the ceiling after a hard afternoon thunderstorm, or a shingle or tile in the yard the morning after one of our coastal wind events.
Wellborn built cabinet lines into a national name, but their roofing division has always focused on a specific segment of the Florida market: metal roof systems and standing-seam panels. That matters, because the failure points on a Wellborn metal roof are completely different from what you’d expect on asphalt shingles. We see the same three issues repeat themselves in neighborhoods like Victoria Park, Rio Vista, and Coral Ridge: seam separation at panel joints, neoprene washer degradation at fastener points, and flashing failures where the roof meets the parapet walls common on 1950s and 1960s Fort Lauderdale construction. The salt air accelerates every one of them.
Key Takeaways:
- Wellborn roofing repairs in Fort Lauderdale: $400 – $1,800 installed
- Full Wellborn roof replacement: $8,000 – $20,000 depending on square footage and pitch
- We stock Wellborn-compatible seam caps, fasteners, and flashing on the truck
- Free written estimate before any work starts – including parts and labor line items
- Mason Remodeling Co Fort Lauderdale is an independent service provider, not affiliated with Wellborn
Which Wellborn Models This Applies To
Wellborn’s roofing line covers three series you’ll see across Fort Lauderdale: the residential standing-seam series (1-inch and 1.5-inch seam profiles), a concealed-fastener wall panel system used on some mid-century modern homes in Sailboat Bend and Tarpon River, and a limited run of metal shingle panels that imitate barrel tile. The standing-seam 1-inch profile is the one we service most often in this area, and it’s also the one that creates the most confusion when owners try to order parts themselves. Here’s the compatibility gotcha that catches people: Wellborn changed their seam geometry slightly around 2015, so seam caps and clips from the older run do not mate cleanly with panels made after the change. The panel width looks the same from the ground, but the cap won’t seat. If you order a seam cap online without checking the manufacturing date on the underside of an existing panel, you’ll get the wrong part about half the time in this market.
OEM Wellborn parts are still available through limited distribution channels, but lead times run longer than most Fort Lauderdale homeowners want to wait during hurricane season. We’ve worked with quality aftermarket equivalents for years and know which brands match the panel profile and gauge thickness closely enough that you won’t see a visible difference or, more importantly, create a new leak point. For the standing-seam series, we keep seam caps, rib closures, z-closures, and neoprene sealing washers in the truck. For the concealed-fastener line, we carry the specific clip profiles those panels require. If we can’t match a part exactly, we’ll tell you that before we open a single carton.
Styles & brands we work with
Signs Your Wellborn Roofing Is Failing
- Water staining at exterior wall intersections, not the open roof field. This almost always points to flashing failure where the roof meets parapet walls or dormers, and it’s the most common Wellborn-specific failure we find in Fort Lauderdale. The original flashing was often installed tight, but twenty years of thermal expansion in our heat-and-rain cycles separates the seal.
- You can hear a faint rattling or ticking sound from the roof during windy afternoons. That’s loose fasteners. On a Wellborn standing-seam system, the neoprene washers under the screw heads dry out and shrink in salt air, which lets the panel lift slightly and the fastener back out. Left alone, it abrades the panel coating and eventually works the screw free entirely.
- Rust streaks running down from the seam caps. Standing-seam roofs are designed to keep fasteners hidden, but if the seam cap has shifted even a quarter inch, the galvanic reaction between the cap metal and panel coating starts showing up as reddish-brown streaks. In Fort Lauderdale’s salt environment, this happens faster than most warranty documents admit.
- White chalky residue washing off the panels into your gutters. That’s not dirt. It’s the coating system breaking down, usually because the original install skipped the rinse cycle or because years of salt film have eaten through the clear coat. Once the base coat is exposed, the metal starts oxidizing.
- Oil-canning you can see from the street. Every metal roof has some oil-canning, but if you can see bulges or waves from ground level that weren’t there when the roof was new, the panels may be binding against the clips and pushing against each other. That’s a sign the clip layout wasn’t right for the panel length, and it gets worse as the metal expands.
Replacement Cost & What’s Included
We price Wellborn roofing work in Fort Lauderdale using parts-and-labor line items, never a single lump number. Here’s what our installed pricing looks like in this market today:
| Service | Typical Range (Installed) |
|---|---|
| Roof repair (flashing, fasteners, isolated panel replacement) | $400 – $1,800 |
| Full roof replacement (standard pitch, standard access) | $8,000 – $20,000 |
| Tile roof repair (if your Wellborn system uses tile profiles) | $600 – $2,500 |
| Metal roof installation (full system, Wellborn-compatible) | $15,000 – $40,000 |
What drives the range: how much of the roof is involved, whether we need a lift or can work from scaffolding, how many penetrations need flashing work, and whether the underlying deck sheathing is still sound. Fort Lauderdale’s building code requires specific uplift ratings for fasteners and clips, and those materials cost more than what you’d buy at a big-box store. Every quote includes the written parts list, the labor hours, and the permit fee if one is required. We pull permits and handle inspections when the job calls for it. And after the work is done, our written guarantee covers the repair for 365 days from the completion date. If something we installed fails in that window, we return and fix it at no charge. No dispute process, no fine print games.
DIY or Call Us?
Here’s the honest answer. There are things a homeowner can safely check on a Wellborn roof, and there are things that will hurt you or hurt the roof itself. From the ground and the attic, you can check for water stains, look at fastener spacing, and inspect your gutters for coating residue. Those are legitimate diagnostic steps. What you should not do is get on a metal roof in Fort Lauderdale without proper safety gear and training. Metal roofs are slick when even slightly damp, and after a morning dew or light rain, that’s most mornings here. We’ve also seen homeowners try to tighten backing-out fasteners themselves and overdrive the screw, which punctures the panel profile and creates a new leak. Or they replace a neoprene washer with a hardware store rubber washer that isn’t UV-stable and crumbles within a season. The restoration of a Wellborn standing-seam system requires specific tools and torque settings that are not worth buying for one repair.
If you can see the problem from the ground and it looks simple, give us a call and describe what you’re seeing. We’ll tell you over the phone whether it’s worth a service visit or something you can handle on your own schedule. Most Fort Lauderdale owners find that a professional repair costs less than the tools and a trip to the ER, but we’ll never push a service call you don’t need at (754) 354-3720.
How Much Does Wellborn Roofing Repair Cost in Fort Lauderdale?
Wellborn roofing repairs in Fort Lauderdale typically cost $400 to $1,800 installed, with most isolated flashing or fastener work landing around $600 to $900. The exact price depends on what failed, how much material we’re replacing, and whether the underlying deck is still sound. Call (754) 354-3720 for an exact quote – our estimates are free and written, never verbal.
See the difference
Before
After
Before
After
Before
AfterCan a Wellborn Roof Be Repaired, or Does It Need Full Replacement?
Most Wellborn roofing issues in Fort Lauderdale can be repaired rather than replaced, especially if the problem is confined to flashing, seam caps, or a small section of damaged panels. Full replacement only makes sense when the coating system has failed across the entire roof surface, the deck sheathing is compromised in multiple areas, or the panel profile is no longer manufactured and repair sections can’t be matched. We’ll show you photos and measurements either way, so you can see exactly what we’re seeing. Call (754) 354-3720 and we’ll give you a straight assessment.
How Long Does a Wellborn Roof Repair Take?
Most Wellborn roof repairs we handle in Fort Lauderdale are done in one visit, and the work itself takes between two and six hours depending on how many panels or flashing points are involved. We carry the common Wellborn-compatible parts on our trucks, so we don’t have to run back to a supply house mid-job for the majority of repairs. If you need a full replacement, that’s a two-to-four day project for a typical Fort Lauderdale roof, and we’ll give you the schedule in writing before we start.
Do You Stock Wellborn Parts on the Truck?
Yes, we keep Wellborn-compatible seam caps, rib closures, z-closures, fasteners with the correct neoprene washers, and flashing stock on our service trucks when we roll into Fort Lauderdale neighborhoods. Not every single Wellborn profile has an exact aftermarket match in our inventory, so for older or less common series we may need to order the specific part. If that happens, we’ll tell you the lead time and cost before you commit to anything. A call to (754) 354-3720 gets you an answer on availability in about five minutes.
Common Wellborn Roofing FAQs
How long should a Wellborn metal roof last in Fort Lauderdale? A Wellborn standing-seam metal roof in Fort Lauderdale should last 25 to 40 years with proper installation, but the coating system and fasteners typically need attention around year 15 to 20 in salt-air environments. Regular inspection of flashing and fastener washers can extend the useful life significantly. Give us a call at (754) 354-3720 and we’ll take a look at what you’re dealing with.
Can you replace just a section of my Wellborn roof, or do you have to do the whole thing? We can replace an isolated section of a Wellborn roof in Fort Lauderdale as long as we can match the panel profile and coating color closely enough that the repair isn’t visible from the street. In some cases, the patina difference between old and new panels makes a full replacement the better-looking option, and we’ll tell you that honestly before you decide. Call (754) 354-3720 and we’ll walk you through the options.
Do you pull permits for Wellborn roof repairs in Fort Lauderdale? Yes, whenever the scope of work requires one under Fort Lauderdale building code. Simple fastener and flashing repairs typically don’t need a permit, but panel replacement or any structural work does. We handle the paperwork and scheduling, and we make sure the work passes inspection. A quick call to (754) 354-3720 will tell you whether your particular repair needs a permit.
Will the price change once you start the work? No. We provide a written price before any work begins, and that’s the price you pay unless we find something structural that was hidden and you approve the change in writing. No surprises. That’s how we’ve operated since Mason Remodeling was founded in 2004, and it’s not optional for us. Call (754) 354-3720 for your written estimate.
Call Us for Wellborn Roofing Parts and Repair in Fort Lauderdale
If your Wellborn roof is showing signs of failure, don’t wait until a Fort Lauderdale thunderstorm turns a small leak into a ceiling replacement. We stock the parts, we know the profiles, and we’ll tell you what we found, what it takes to fix it, and what it will cost – before we touch a thing. Call (754) 354-3720 to schedule your free estimate. When you call, a live person answers, and we’ll get you on the schedule without the runaround.
Written by Isaac Pruett, Owner, Mason Remodeling Co Fort Lauderdale at Mason Remodeling Co Fort Lauderdale, serving Fort Lauderdale and nearby areas.
