Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Roofing: The Fort Lauderdale Owner’s Guide
Unilock-compatible roofing parts and replacements in Fort Lauderdale typically run $400 – $1,800 installed depending on the component, and most swaps are completed in a single visit once the part is matched to your system. You usually discover a Unilock roofing failure the hard way: a damp spot on the ceiling after a hard South Florida downpour, a missing cap that the last storm peeled loose, or granules collecting in your gutter faster than they should. The good news is that the parts are identifiable, the fixes are straightforward when caught early, and you don’t have to guess at pricing before anyone sets foot on your property.
Mason Remodeling Co Fort Lauderdale is an independent service provider. We are not affiliated with Unilock, but we stock and install Unilock-compatible roofing components across Fort Lauderdale and match them by spec, not by guesswork.
Key takeaways:
- Most Unilock roofing part replacements in Fort Lauderdale cost $400 – $1,800 installed
- We identify your part by model marking, measurement, or photo before quoting
- Written price before any work starts, every time
- 365-Day Done Right Promise covers the workmanship for a full year from completion
Which Unilock Models This Applies To
Unilock manufactures several roofing product lines, and the compatibility question is where homeowners in Fort Lauderdale run into trouble. The most common systems we service are the Unilock stone-coated steel panels and their corresponding ridge caps, hip caps, and flashing components. These are not interchangeable with generic metal roofing caps from a big-box store. The profile, the screw spacing, and the finish thickness all differ by series, and a cap that looks close from the ground will leak if it’s off by a half inch.
The fastest way to identify your part is to check the underside of a loose panel or cap for a stamped code or series marking. If you can’t find a stamp, measure the cap width and the rib spacing precisely, and take a daylight photo of the profile from the side. We match Unilock parts by those measurements when the label is gone. On the OEM-versus-aftermarket question: there are quality aftermarket caps and flashing pieces that meet Unilock’s profile specs, but this is one place where we lean OEM if it’s available. The finish on Unilock stone-coated panels is specific, and a mismatched cap looks wrong from the curb in a Fort Lauderdale neighborhood where roofing color matters to resale.
One compatibility gotcha we see often in Victoria Park and Rio Vista: older Unilock installations from the early 2000s used a slimmer profile than current production. If your home was re-roofed before 2010, we need the measurements, not just the series name, because the same series designation changed profile width at least once. That’s the kind of detail that keeps a replacement from leaking a month later.
Styles & brands we work with
Signs Your Unilock Roofing Is Failing
- Loose or missing ridge caps. South Florida wind loads are relentless, and the first components to go are always the caps along the ridge and hips. A lifted cap lets water run sideways under the panel system, which rots the decking before you ever see a ceiling stain.
- Granule buildup in gutters. Unilock stone-coated panels shed a small amount of granules when new, but steady accumulation after year five usually means the coating is breaking down from UV exposure and salt air. In Fort Lauderdale, that salt air shortens coating life compared to inland installs.
- Rust streaks below fasteners. Every screw on a metal roof is a potential entry point. When the neoprene washer under the screw head hardens and cracks, water seeps along the threads and rusts the panel from the inside out. A rust streak is the tell.
- Flashing separation at walls or chimneys. The transition where the roof meets a vertical wall is the most common leak point on any metal system. On Unilock installs we walk, separation there usually traces back to a short-cut at install time, not a product fault.
- Daylight visible in the attic. Walk the attic on a bright morning and look up. If you can see pinholes of light anywhere other than vents, water has a path in. Pin size holes become quarter-size problems after one hurricane season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Parts replacement on Unilock roofing in Fort Lauderdale runs $400 – $1,800 installed for most single-component fixes. A ridge cap replacement with matching finish typically lands between $400 and $900 including fasteners and sealant. Flashing replacement around a chimney or wall junction runs $600 – $1,200 depending on access. Full panel replacements that require removing and resetting surrounding panels fall on the upper end, $1,200 – $1,800, because the work is more surgical.
What drives the range is access and condition. A single-story hip roof with good decking underneath is fast. A two-story job near Victoria Park with rotted decking at the leak point will cost more because the rotten sheathing has to be cut out and replaced before the roofing goes back on. You get a written line-item price before any work starts. No verbal estimate that grows on the final bill. Every completed repair carries our 365-Day Done Right Promise: if the work is not right within a year of completion, we make it right at no cost to you.
If the roof itself is beyond repair, a full roof replacement in Fort Lauderdale runs $8,000 – $20,000. We’ll tell you plainly if patching a failing system is throwing good money after bad, and the repair estimate you already paid for gets credited toward the replacement.
DIY or Call Us?
There are two things you can safely check from the ground: missing caps and visible rust streaks. Everything else involves getting onto a roof, and in Fort Lauderdale, that means working on a surface that is either rain-slick, moss-slick, or baking hot for most of the year. Falls from a roof are not a lesson you want to learn twice.
If you insist on tightening a loose screw, use a drill with a depth-limited clutch and replace the neoprene washer. Over-tightening a metal roof fastener is how you crack the washer and create the exact leak you were trying to prevent. And never walk a stone-coated panel from the middle; the coating is tougher than paint but it will chip under a misplaced step. For anything beyond a visual check from the ground, call (754) 354-3720. An estimate is free, and you’ll know the cost before we touch a thing.
FAQs
Stone-coated steel panels typically hold up 40 – 70 years nationally, but in Fort Lauderdale’s salt air, the fasteners and flashing fail long before the panels do. The washers under the screws harden in about 10 – 15 years here. Budget for fastener and flashing maintenance well before the panel coating gives out. Call (754) 354-3720 and we’ll assess what needs attention now versus what can wait.
Yes, the same way you can patch a tire, up to a reasonable number of patches. One bad cap, one failed flashing, one rusted fastener: repair is straightforward and costs $400 – $1,800. But if the coating is shedding granules across the whole roof, it’s a replacement. We’ll show you photos and explain the honest math before you spend a dollar. Call (754) 354-3720 for a free estimate and a straight answer.
Most single-component replacements take two to four hours on site, plus the time to match and order the part if it’s not already on our truck. We keep common Unilock-compatible caps, fasteners, and flashing in stock for Fort Lauderdale jobs, and uncommon pieces are usually two to three days out from our suppliers. Call (754) 354-3720 and we’ll give you a realistic schedule, not a best-case one.
We stock the parts ourselves and handle the ordering. You bring us a photo, a measurement, or a stamped code from the part, and we match it. We also stock compatible parts for KraftMaid cabinetry and Cambria and Silestone surfaces if other parts of the home need attention. Call (754) 354-3720 and we’ll verify the part before you pay for anything.
We tell you what we found, what it takes to fix it, and what it will cost before we touch a thing. Call (754) 354-3720 to schedule your free estimate. A live person answers, any hour, any day. You’ll get a written price and the name and photo of the technician before they arrive, wearing a clean uniform and a photo ID badge at your door.
Written by Isaac Pruett, Owner, Mason Remodeling Co Fort Lauderdale at Mason Remodeling Co Fort Lauderdale, serving Fort Lauderdale and nearby areas.
