Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Roofing: The Fort Lauderdale Owner’s Guide
We stock and install Mr-Glass roofing replacement parts and full system repairs across Fort Lauderdale, with most common part swaps running $400 – $1,800 installed depending on what failed and how deep the damage goes. If you’ve got a Mr-Glass roofing component that’s cracked, leaking, or pulling away from the structure, we can usually match the part, get it on the truck, and have it installed same week. Most owners discover the problem the same way: a water stain on the ceiling after a hard South Florida downpour, or a piece of flashing they spotted hanging loose after a wind gust off the Atlantic.
Here’s the thing about Mr-Glass roofing components in Fort Lauderdale specifically: the salt air, UV intensity, and hurricane-season wind cycles put stress on parts that would last decades in a milder climate. We’ll tell you what we found, what it takes to fix it, and what it will cost, before we touch a thing. That’s how Isaac Pruett runs every job that rolls through Mason Remodeling Co Fort Lauderdale.
Which Mr-Glass Models This Applies To
Mr-Glass roofing systems typically fall into two categories: the glass-panel skylight and sunroom series, and the structural glass canopy/awning lines used on some Fort Lauderdale patio covers and entryways. The part compatibility difference between them matters more than most homeowners expect. Skylight-series panels use gasket and seal specifications that don’t cross over to the canopy line, even when the glass dimensions look identical at a glance.
How to identify what you have: check the aluminum frame edge for a stamped serial or model code, usually etched on the interior side of the rail. If that’s faded, measure the glass thickness with a caliper. The residential skylight line runs 3/16″ to 1/4″ tempered glass; the canopy series runs 5/16″ to 3/8″ laminated. We carry OEM Mr-Glass gaskets, seal kits, and flashing sets for both lines, plus quality aftermarket equivalents where the OEM part has been discontinued. One compatibility gotcha we see regularly in Fort Lauderdale: older Mr-Glass installations from the mid-2000s used a proprietary corner key that’s no longer manufactured. We machine replacements in-house for those because a retrofit kit changes the frame geometry and creates leak points.
Styles & brands we work with
Signs Your Mr-Glass Roofing Is Failing
- Water staining on the ceiling or wall below the glass panel. This almost always means the perimeter gasket has compressed or cracked, letting moisture wick past the seal and travel along the frame channel before it finds a way out.
- Condensation or fogging between glass layers. For laminated or double-pane Mr-Glass panels, this indicates a failed seal at the edge. It’s not cosmetic. Once the seal goes, the insulating value drops and the panel can eventually delaminate.
- Visible cracking or crazing in the glass surface. Fort Lauderdale sun and salt exposure accelerate stress fractures, especially on panels installed before 2010. Small cracks spread fast once wind pressure gets involved.
- Loose or lifting flashing at the roofline connection. Flashing is the metal or membrane transition where the Mr-Glass frame meets your roof deck. When it lifts, water gets underneath during any heavy rain, and Fort Lauderdale gets plenty of those.
- Frame corrosion or white powdery residue on aluminum. This is galvanic corrosion from salt air exposure. Left alone, it eats through the frame channel and compromises the entire assembly’s structural hold.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Fort Lauderdale homeowners, typical Mr-Glass part replacement and repair falls into these installed ranges:
| Service | Installed Price Range |
|---|---|
| Gasket and seal replacement (single panel) | $400 – $900 |
| Flashing repair or replacement | $500 – $1,200 |
| Glass panel replacement (tempered, residential skylight) | $800 – $1,800 |
| Frame repair with corrosion treatment | $600 – $1,500 |
What drives the range: panel size, whether we’re working on a one-story or two-story roofline, how much frame repair is needed around the failed part, and whether the original flashing is salvageable. Every quote is a written price before any work starts. No surprise invoices, no verbal estimate that grows on the final bill. That’s been the Mason Remodeling Co Fort Lauderdale standard since day one, and it applies to a $400 gasket swap the same as a full roof replacement.
DIY or Call Us?
Here’s the honest version. You can safely check a few things yourself: look for visible cracks in the glass, run a hand along the interior frame to feel for wetness after rain, and check whether any flashing looks lifted from the ground with binoculars. What you shouldn’t do is get on a Fort Lauderdale roof, especially a tile roof, and start pulling sealant or loosening frame bolts. Roof work at height with glass involved is genuinely dangerous. A slip on a sun-baked tile roof is a life-changing injury, not a Saturday project, and a dropped panel doesn’t just break itself, it takes out whatever is below it.
If you’re not sure whether what you’re seeing is a real failure or just normal wear, call us at (754) 354-3720. We’ll talk you through what to look for, and if it needs a visit, you’ll know exactly who’s coming, what they’ll check, and what the visit costs before anyone sets foot on your property.
FAQs
In Fort Lauderdale’s salt air and UV exposure, Mr-Glass gaskets and seals typically last 8 – 12 years, glass panels 15 – 20, and aluminum frames 20+ with proper maintenance. The marine environment cuts lifespan by roughly 30% compared to inland Florida installations. Call (754) 354-3720 for an inspection if your system is nearing those windows.
Gaskets, sealant, and minor flashing issues can usually be repaired. Crazed or delaminated glass cannot, the panel must be swapped. We’ll give you an honest read on which path makes sense before you spend a dollar.
Most single-panel gasket or seal replacements take 2 – 4 hours on site. Full glass panel or flashing replacements usually run 4 – 8 hours depending on access. We schedule a specific day, show up with the part on the truck, and clean the work area before we leave.
We keep common Mr-Glass gaskets, seal kits, and flashing sets in our Fort Lauderdale stock, and we machine discontinued corner keys in-house. Glass panels are cut to spec per order, which typically takes 3 – 5 business days. For an exact availability check on your model, call (754) 354-3720.
Written by Isaac Pruett, Owner, Mason Remodeling Co Fort Lauderdale at Mason Remodeling Co Fort Lauderdale, serving Fort Lauderdale and nearby areas.
