Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Roofing: The Fort Lauderdale Owner’s Guide
We stock and install CWS-compatible roofing parts in Fort Lauderdale, with most roof repair jobs running $400 – $1,800 and full replacements between $8,000 – $20,000 depending on the damage and the system’s age. If you’re reading this because water showed up on the ceiling or a shingle went airborne during the last storm, you’re in the right place. Most CWS roofing failures we see start small, a cracked flashing, a slipped tile, a seam that opened up after a few too many Florida summers, and then the first heavy rain turns it into an emergency.
Mason Remodeling Co Fort Lauderdale is an independent service provider and not affiliated with CWS. We work on their systems every week and stock the common wear parts on our trucks, so you’re not waiting on a special order when the problem is urgent.
Which CWS Models This Applies To
CWS roofing systems in Fort Lauderdale fall into two broad camps: standing-seam metal profiles and the coated-steel tile systems that mimic barrel or flat concrete tile. Within each, the compatibility gotcha is the panel width and seam profile. CWS standing seam has a 16-inch panel width with a 1.75-inch seam rib on most Florida-installed residential jobs, but we’ve measured plenty of 12-inch panels on older custom homes in Victoria Park and Rio Vista that were spec’d differently. Before we order anything, we pull a panel and measure. It takes ten minutes and it prevents the wrong part showing up on install day.
For coated-steel tile systems, the failure point is almost never the tile face itself. It’s the underlayment, the fasteners, or the flashing detail at the ridge and valleys. If your CWS roof is 15 years old and “looks fine from the street,” the underlayment under those tiles has been cooking in South Florida heat for over 5,000 days. That’s the honest assessment we give at the free estimate. OEM CWS parts are available for most current series, but we regularly install quality aftermarket flashing, underlayment, and fasteners that meet or exceed the original spec for less money. We’ll show you both prices in writing before any work starts. That’s how Isaac Pruett runs every job, and it’s been that way since the company started in 2004.
Styles & brands we work with
Signs Your CWS Roofing Is Failing
- Water staining on ceilings or walls after rain. This usually means a flashing detail failed, not the roofing material itself. On CWS tile systems, the pipe boot or valley flashing is the prime suspect. The stain shows up far from the actual leak because water travels along the trusses before it drips.
- Loose or missing fasteners visible from the ground. Coated-steel systems use screws with rubber washers. When the rubber degrades from heat and UV, water wicks down the screw shaft. In Fort Lauderdale, those washers start failing around year 8 to 10, regardless of the steel’s 30-year rated life.
- Granular grit washing into your gutters. If your CWS system includes an asphalt-based component or ridge cap, granule loss means the mat is breaking down. On the tile-look systems, grit in gutters often comes from failing mortar at the hip and ridge lines.
- Visible rust streaks or pinholes at seams. Salt air accelerates corrosion on any coated steel. Homes east of Federal Highway in Fort Lauderdale see this years earlier than the western neighborhoods. We inspect the seam lap and the fastener heads first.
- You hear metal tick or pop on hot mornings. Thermal expansion is normal, but loud popping at the same spot every day can mean a fastener has backed out and the panel is moving. Left alone, the panel can work itself loose entirely in the next storm.
Replacement Cost & What’s Included
In Fort Lauderdale, you should budget as follows, and these are real numbers we put in writing before any work starts:
- Roof repair (flashings, fasteners, small sections): $400 – $1,800
- Tile roof repair (CWS tile profile, trim and fasteners): $600 – $2,500
- Full roof replacement (CWS-compatible system): $8,000 – $20,000
The range comes down to roof size, pitch, the amount of decking that needs replacement once we open it up, and whether you have one or two layers to remove. Every estimate includes parts, labor, disposal, and a written line-item breakdown. Our workmanship is covered by a written guarantee for 365 days from completion. If something fails in that window, we return and fix it at no charge, no dispute process. The 365-Day Done Right Promise is standard on every roof we touch, never an add-on.
DIY or Call Us?
You can safely check your own roof from the ground: look for missing fasteners, lifted ridge caps, visible rust, and granules in the gutter. You can pull back a ceiling stain and see if the drywall is soft. What you should not do is get on a Fort Lauderdale roof, especially a metal one, after it’s rained or when it’s above 85 degrees, which is most of the year. CWS steel gets slick with condensation, the pitch on Florida ranch and mid-century homes is steeper than it looks, and a fall from even a single-story roofline changes lives. If you see signs of failure, call (754) 354-3720 and we’ll come out, inspect, and hand you a written price in plain language. We tell you what we found, what it takes to fix it, and what it will cost, before we touch a thing.
See the difference
Before
After
Before
After
Before
AfterHow much does CWS roof repair cost in Fort Lauderdale?
Most CWS roof repairs in Fort Lauderdale run $400 – $1,800, with tile-specific repairs ranging $600 – $2,500. The spread depends on what failed, how much flashing or underlayment is involved, and whether we’re matching an existing CWS profile or upgrading a failing detail. Call (754) 354-3720 to schedule a free estimate and we’ll put an exact number in writing.
Can a failing CWS roof section be repaired instead of replaced?
Yes, if the steel or tile surface is still solid and the failure is isolated to flashings, fasteners, or ridge lines. If the underlayment has deteriorated or the panels are rusted through, patching it becomes a losing game and we’ll tell you that plainly. The free estimate tells you which path makes sense before you spend anything.
How long does a CWS roof part swap take in Fort Lauderdale?
A typical flashing, fastener, or small section repair takes one day, sometimes half a day. Full CWS-compatible replacements in Fort Lauderdale usually take two to five days depending on size, tear-off, and weather. We give you a schedule in writing with the estimate, and we show up when the schedule says we will.
Do you stock CWS-compatible parts in Fort Lauderdale?
We keep common CWS-compatible flashings, fasteners, underlayment, and sealants on our trucks so most repairs don’t wait on shipping. For unusual CWS series profiles or discontinued colors, we special-order and give you the timeline up front. We also stock parts for KraftMaid, Cambria, and Silestone systems on the interior side, which matters if a roof leak has done damage below.
Written by Isaac Pruett, Owner, Mason Remodeling Co Fort Lauderdale at Mason Remodeling Co Fort Lauderdale, serving Fort Lauderdale and nearby areas.
