Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Fort Lauderdale Owner’s Guide
If you own a home in Fort Lauderdale with a CGI kitchen installation and something has failed, we can source or match the compatible components and install them. Typical CGI kitchen remodeling work in Fort Lauderdale runs $14,000 to $45,000, and we schedule most single-part replacements within a week of diagnosis. What usually brings a homeowner to this page is a hinge that snapped, a drawer slider that gave out, a cabinet face that’s delaminating from humidity, or a countertop seam that opened up after years of Florida heat and moisture.
We’re an independent remodeling contractor, not affiliated with CGI. That matters because it means we’re free to tell you the truth about what’s worth fixing, what’s worth replacing, and when an aftermarket part will outlast the original. Isaac Pruett, our owner, has spent nearly twenty years running projects across South Florida, and he’s seen CGI components hold up well in Fort Lauderdale’s salt air and humidity, but certain failure points repeat. You’ll find those laid out below.
Which CGI Models This Applies To
CGI kitchen cabinetry and components turn up across a range of Fort Lauderdale homes, from Victoria Park condos to single-family houses in Coral Ridge. The compatibility question starts the same way every time: what does the label say? Open the cabinet door and look at the inside of the frame or the underside of a drawer box. CGI typically stamps a series code, a finish code, and a production date. If the sticker is gone, measure the drawer opening and the door overlay. CGI cabinets run both inset and full-overlay configurations, and mixing them up is the most common ordering mistake we see.
When it comes to replacement parts, you have two honest options. OEM CGI parts are factory-matched: same finish, same drill pattern, same profile. They’re the right call when you need a visual match on a visible door front or drawer face, especially on a kitchen that’s less than five years old. Quality aftermarket parts, mostly hinges and slides made by brands like Blum or Salice, can often be substituted for hidden hardware, and in our experience they sometimes outlast the originals because they’re rated for heavier use. For visible surfaces, stick with OEM or a custom milled match. For hidden hardware, aftermarket is usually the smarter money in Fort Lauderdale, where humidity and salt air are harder on metal than anything else.
Styles & brands we work with
Signs Your CGI Kitchen Remodeling Is Failing
- A drawer that sticks, sagging, or scraping. The culprit is usually a worn-out slide or a warped box from moisture. Fort Lauderdale’s humidity gets inside cabinets, and particleboard drawers don’t forgive that. Once a drawer starts scraping, the slide is already damaged enough that lubricant won’t save it.
- A door that won’t stay closed or sits crooked. This is almost always a hinge failure, often the clip mechanism on a soft-close hinge. The hinge loses tension, the door drifts open, and before long the door pulls on its screws and strips the holes in the frame.
- Peeling or bubbling laminate on door fronts or cabinet ends. CGI laminate doors delaminate at the edges first, especially near the dishwasher or sink. Heat and steam work the adhesive loose. Once it bubbles, there’s no re-adhering it permanently; the door front needs replacement.
- A countertop seam that has opened or shifted. If the original install was done with a cheap adhesive or without proper underlayment support, Florida’s heat cycles move the seam over time. It gets worse, not better, and ignoring it lets moisture into the substrate.
- Soft-close hardware that slams. The damper inside the hinge or slide has blown out. It’s a small part, but when one goes, the rest of them on that cabinet run are usually not far behind, since they’ve all seen the same number of open-close cycles.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a single failing component, the installed cost in Fort Lauderdale falls inside a few clear bands. Cabinet hardware replacement (hinges, slides, soft-close dampers) runs $125 to $450 per cabinet, depending on the hardware tier and how many internal parts are being swapped. A single door front replacement runs $150 to $500, including finishing and color matching. A full door-and-drawer-front refacing job lands between $4,000 and $13,000. A complete kitchen remodel with CGI-compatible cabinetry starts at $14,000 and tops out around $45,000 for larger footprints with custom inserts.
Every Mason Remodeling Co Fort Lauderdale job comes with a written price before any work starts, not a verbal estimate that drifts. You’ll know the part cost, the labor cost, and the warranty terms in writing. If the work doesn’t hold up within 365 days of completion, we come back and make it right at no charge. We tell you what we found, what it takes to fix it, and what it will cost, before we touch a thing.
DIY or Call Us?
Some checks are safe for a homeowner to do alone. You can confirm the model code, measure the drawer opening, and identify whether the finish is matte, gloss, or textured. You can inspect the hinge screws and the door alignment by eye. What you should not do is force a seized drawer, pry a delaminated laminate face, or attempt to re-adhere any surface with epoxy you bought at a hardware store. We’ve followed behind enough of those attempts in Fort Lauderdale to know they usually turn a $200 hardware fix into a $500 damage repair.
If the part is visibly failed, skip the guesswork. Call (754) 354-3720. We’ll identify what you have, tell you what we’d replace it with, and put the price in writing before we schedule anything.
FAQs
Hinges and slides typically last 10 to 15 years in Fort Lauderdale’s climate, though soft-close dampers often fail closer to the 8-year mark. Laminate door fronts near heat and moisture sources can show edge lift sooner. If you’re past year ten and one part has failed, expect the rest of the hardware on that run to follow.
For stripped hinge screws and minor door misalignment, yes, we repair that routinely. For a blown soft-close damper, delaminated laminate, or a seized drawer slide, replacement is the honest answer, and it’s usually less expensive than trying to resurrect a part that’s already at the end of its service life. Call (754) 354-3720 and we’ll tell you straight which path applies.
A single hardware swap on one cabinet takes an hour or two. A door front replacement runs one to two days, accounting for finish matching and adjustments. A full kitchen remodel in Fort Lauderdale runs two to six weeks depending on scope, and the timeline is stated in the written price before we start.
We stock common CGI-compatible hinges, slides, dampers, and mounting plates on our service vehicles. Finishes vary, so we may need to order specific colors or profiles, which adds a few days. We also work with KraftMaid, Cambria, and Silestone products for countertop matches. Call (754) 354-3720 and we’ll confirm what’s available for your model before you schedule.
Written by Isaac Pruett, Owner, Mason Remodeling Co Fort Lauderdale at Mason Remodeling Co Fort Lauderdale, serving Fort Lauderdale and nearby areas.
